Reloading Tools

Rcbs universal hand priming tool w/universal shellholder

FEATURES
-Combines the universal shell holder from the APS® tool with the primer tray
from the standard toolto offer unmatched performance
-Accepts cases from .32 ACP to .45-70 Government
-The safety gate isolates the primer seating operation from the primer supply to
reduce the risk of tray detonation
-The removable primer tray orients their primers for use & will fit any manufacturer’s
primer packaging
-Includes accessories to seat large & small rifle or pistol primers

Rcbs fl die set.22-250 gp-a

FEATURES
-Caliber: .22-250
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

Rcbs collet for bullet puller.338 caliber

FEATURES
-Caliber: .338 Cal
-This collet is designed to be used with the RCBS® Standard Bullet puller to remove bullets from a wide
range of cases

Rcbs stuck case remover

FEATURES
-Extracts stuck cases from standard sizer dies without damaging the die
-Uses a very simple two-step removal process

Rcbs rebel single stage press master reloading kit
Other Features: Kit contains: rebel press, uniflow-iii powder measure, 1500 grain digital scale, hand priming tool, power pull bullet puller kit speer #15 manual, fold up hex key set, primer pocket brushes , deburring tool, case loading block, case spray lube, 2 case neck brushes, powder funnel.

Lee factory crimp die only.38-55 winchester

FEATURES
-Factory crimp die for .38-55 Winchester
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation

Lee full length 3-die set.444 marlin

FEATURES
-Pacesetter 3 die set for .444 Marlin
-Full length sizing die
-Bullet seating die
-Factory crimp die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee full length 3-die set.257 roberts

FEATURES
-Pacesetter 3 die set for .257 Roberts
-Full length sizing die
-Bullet seating die
-Factory crimp die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee full length 3-die set.30-06 springfield

FEATURES
-Pacesetter 3 die set for .30-06 Springfield
-Full length sizing die
-Bullet seating die
-Factory crimp die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee double cavity mold.451 ball w/handles

FEATURES
-Double Cavity Mold
-Produces a .451 diameter ball
-137.71 grains
-Includes handles

Rcbs vibratory case polisher 120vac 14lbs.Capacity
Other Features: Sifter lid

Rcbs case cleaner concentrate 1 quart makes 10 gallons

FEATURES:
-Use w/ Ultrasonic & Rotary style case cleaner/polishers
-Removes tarnish, carbon buildup & metal oxides from cartridge cases
-Non-corrosive/non-combustible
-Thoroughly cleans brass cases
-Concentrated - one quart makes 10 gallons of solution
-Contains anti-tarnish additive to keep cases looking shiny & new

Other Features: For rotary and ultrasonic case cleaners

Rcbs fl die set 6.5 wby rpm

Rcbs small base die set.308 winchester

FEATURES:
-.308 Win.
-Forbottleneck type cases used in tight-chambering semi-automatic, pump or lever-action rifles
-Consists of a Small Base Sizer with an Expander-Decapping Unit & Regular Seater Die with Seater Plug
-The sizer resizes cases below SAAMI minimums, reducing the shoulder & body by a few thousandths
-It also deprimes the case
-The Seater Die has a built-in roll crimper to secure the bullet at the same time it's seated
-To seat bullets without crimping, simply unscrew the die until the crimp ring no longer engages the case
mouth

Rcbs fl die set.308 win.Gp-a

FEATURES
-Caliber: .308 Winchester
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

Rcbs fl die set.300 win.Mag.Gp-a

FEATURES
-Caliber: .300 Winchester Magnum
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

Rcbs fl die set.30-30 win.Gp-a

FEATURES
-Caliber: .30-30 Winchester
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

Rcbs shell holder #4

FEATURES
-Shell Holder #4
-Built from hardened steel
-Designed to properly align the case with the reloading die in single-stage & turret presses
-Sized to fit specific case heads & capture 0.125" of the case head for proper SAAMI head spacing

Lee full length 2-die set.32 winchester special

FEATURES
-Full length 2 die set for .32 Winchester Special
-Full length sizing die
-Bullet seating die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee full length 2-die set.35 whelen

FEATURES
-Full length 2 die set for .35 Whelen
-Full length sizing die
-Bullet seating die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee ultimate 4-die rifle set.270 winchester

FEATURES
-Ultimate 4-die set for .270 Winchester
-Full length resizing die
-Collet necksizing die
-Easy adjust dead length bullet seating die
-Factory Crimp Die
-Shell holder
-Powder measure
-Load data

Other Features: Includes collet neck sizer die and factory crimp die.

Lee double cavity mold.452-255-rf w/handles

FEATURES
-.452 diameter
-255 grain
-Roundnose bullet
-Suitable for cartridges like.45 ACP, .45 Colt
-Handles included

Lee carbide 3-die set.30 m1 carbine

FEATURES
-For .30 M1 Carbine
-3-die set
-Carbide full length sizing die
-Bullet seating die
-Powder thru expanding die
-Universal shell holder
-Powder dipper
-Instructions/load data

Lee precision lead melter holds 4 lbs.Of lead 500 watt

FEATURES
-High speed melter
-Infinite heat control
-Easily handles 4-cavity molds
-Takes less than 15 minutes to melt 4 pounds of metal
-500 watts AC only
-The pot has a 2.9" opening & is 2" deep

Lee six cavity mold 9mm 124gr tc no handles

FEATURES
-Six Cavity Mold
-.356 Diameter
-124 grain
-Truncated Cone nose bullet
-Suitable for cartridges like 9mm Luger, .38 Super Auto, etc.
-Lube & handles sold separately

Lee double cavity mold 309-170-f w/handles

FEATURES
-.309diameter
-170 grain
-Round nose bullet
-Suitable for cartridges like .30 caliber rifle
-Handles included

Mec powder bushing #17

FEATURES
-View MEC's Powder Bushing Chart & Charge Bar Selection information:
https://www.mecshootingsports.com/Images/document/PowderBushingChart.pdf

Mec powder bushing #9

FEATURES
-View MEC's Powder Bushing Chart & Charge Bar Selection information:
https://www.mecshootingsports.com/Images/document/PowderBushingChart.pdf

Mec powder bushing #8

FEATURES
-View MEC's Powder Bushing Chart & Charge Bar Selection information:
https://www.mecshootingsports.com/Images/document/PowderBushingChart.pdf

Mec jig fixture for shotshell reloaders
Other Features: Can be mounted to bench,board, or be free standing,securely holds & is adjustable.For 600jr,650,700 vers,sizemaster, steelmaster,grabbers,9000g/h

Lee double cavity mold.452-230-2r w/handles

FEATURES
-.452 diameter
-230 grain
-Round nose bullet
-Suitable for cartridges like.45 ACP, .45 Colt
-Handles included

Mec loader auto indexing grabber.410 2 1/2" 012

FEATURES
-.410 bore
-1/2 oz. charge bar
-Bushings: 10, 11, 12
-Works on six shells at once
-Fully automatic primer feed
-Auto-cycle charging
-Three-stage crimp
-"Power Ring" resizer
-Automatic indexing
-Finished-shell ejection
-Auto-Dex™ automatically moves the shells through each reloading stage by
simply returning the handle to the top of its stroke

Other Features: 10 11 12 powder bushing 1/2 oz.Bar